Additive Manufacturing Products By 3DINNOVATIONS

• Belt type : GT2
• Width : 6 mm
• Pitch : 2 mm
• Color : White
• Material : Polyurethane (PU) with steel core

• Idler pulley with 16 teeth GT2 timing pulley
• Quantity : 1 pc
• Bore size : ? 3 mm
• For Belt : GT2 timing belt of 6 mm width
• Material : Aluminum alloy

• Nozzle Input Diameter: 1.75mm, Output Diameter: 0.2mm 0.4mm 0.6mm 0.8mm
• Installation- external M7 thread connection for 1.75mm PLA ABS printer
• Smooth mating face, effectively prevent filament from leaking
• Chamfer design, much easier for filament feeding
• Bright brass nozzle appearance, Carved Nozzle diameter size, easier to be identified

• Product Name: Linear Rail Shaft Support; Model: SK16
• Material: Aluminum; Color: Silver Tone
• Fit for Shaft Dia.: 16mm; Total Size: 48 x 16 x 44mm (L*W*H)
• Mount Hole Distance: 38mm; Mount Hole Dia.: 5.5mm/0.22-inch
• Package Content: 2pcs x Linear Rail Shaft Support

• Thermistor Color : white,Cartridge Heater Material: 304 Stainless Steel
• Voltage: 24v, Power: 40w,Diameter: 6mm ; Length: 1M
• Temperature sensor 100K? accuracy of ? 1%
• Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring
• Package Included: 3pcs x 1M 24V Cartridge Heater; 3pcs x 1M NTC Thermistor

• When there is material, the level signal of the detection port should be high. When there is no material, the level signal of the material port becomes low, and the system detects one. If the high to low conversion is determined, the material is consider
• Suitable for 3D printer run-out, pause detection.
• Use on lerdge board: the green light for the module is always on when material is available. When the material is used up, the green light goes out. The main board executes the pause command operation and waits for the personnel to replace the material.
• Lerdge main board wiring: M sensor port on the main board.
• For other boards: material detection module uses level jump detection Use on lerdge board: the green light for the module is always on when material is available. When the material is used up, the green light goes out. The main board executes the pause command operation and waits for the personnel to replace the material.

• Model: LMK12UU
• Material: Steel
• Inner Dia.: 12mm; Outer Dia.: 21mm
• Square Hight: 6mm ; Total Size: 30x32x32mm
• Included: 1x LMK12UU Linear Bearing ; Net Weight: 57g

• Precise Leveling - Metal nut is more powerful and will twist more tightly than plastic nuts. Upgraded leveling nut of large size makes leveling easier, The torque of these nuts is large, making it easier to fine tune the hotbed.
• Easy to Install and Level - It doesn't occupy the printing volume due to reasonable design with easy installation
• Upgraded Bed-level Springs - These level springs more stiff and accurate bed leveling. The die springs are stiffer than ordinary spring, which help your 3D printer much more stable while printing.
• Compatible with Most Hot Bed - Upgraded Aluminum Hand Twist Level Nut. These red aluminum nuts are original upgraded replacement parts for Ender 3/3 Pro/3 X, Ender 5/5 Plus/ 5 Pro, CR-10, CR-10 V2, CR-10 Max, CR 10, CR-10 Mini, CR-10S, CR 10S Pro, CR-10 Plus, CR-X, CR 20.
• Official High Quality - Made by high-quality aluminium alloy, last much longer your stock plastic nuts. Package includes: 4x Hand Twist Leveling Nut, 4x Hot Bed Spring

• Voltage: 12V, Power: 50W, Head diameter: 6mm, Head length: 20mm, Total length:2 Meter
• From the original ordinary 0.3-line high-temperature line to 0.6-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
• From the original 40W power up to 50W, therefore, the maximum temperature increases from 300-310 to 340-350 or so.
• The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
• Nice for 3D Printer, such as CR-10S Pro, CR-X, Ender 3, Ender 3X. Package includes 1 pc Ceramic Cartridge Heater Wire

• Product name: Long type linear bearing slide units
• Type: Double length open type SCS8LUU
• Inner bore (inner dia.): 8mm/0.31''
• Overall Size: 58 x 34 x 22mm/1.02\" X 1.34\" X 0.87''
• Material: metal, rubber; Package:1pc pillow block bearing

• Original Aluminum Drive Feed for Creality 3D CR-7, CR-8, CR-10, CR-10 S4, CR-10 S5, it is stable and durable
• MK8 extruder drive feed kit, can replace acrylic parts of CR-10, CR-10 S4, CR-10 S5.
• Full Metal Aluminum Alloy
• Used for 1.75mm filament
• DIY Aluminum Block Left Hand Side , need to assembly by yourself

• Nozzle diameter:0.4mm, Throat/Heatbreak inside PTFE Tube
• For filament types:1.75mm PLA/ABS
• Extrusion head voltage 12V, Power 40W
• Thermistor: 100K; NTC B value: about 3950
• Melt High-temperature materials - up to 260 C degree with integrated thermistor 100K.

• Product Name: Linear Rail Shaft Support; Model: SK10
• Package Content: 2pcs x Linear Rail Shaft Support
• Material: Aluminum; Color: Silver Tone
• Fit for Shaft Dia.: 10mm/0.4-inch; Total Size: 42(+/-2) x 14(+/-2) x 33(+/-2) mm (L*W*H)
• Mount Hole Distance: 33mm; Mount Hole Dia.: 5.5mm

• Dimensions 214mmx 214mm
• Laminate FR4 1.6+-0.15mm, 2 layer, 35?m copper
• Red Soldermask - both sides, White Silkscreen - both sides
• Power Input: 12V or 24v, Copper plated holes, Upgrade version of MK2A
• Resistance between 1.0 and 1.2 ohm

• Screw diameter :8mm
• Length: 400mm
• Screw spacing: 2mm
• Lead of thread :8mm
• Material: Stainless steel- lead screw, brass- nut

• Works well with Anet A8 3D printer.
• Pretty solution for auto-adjusting heatbed level.
• 10-30V DC working voltage, output NPN.NO
• Anti-jamming three-wire, 140cm / 55.1in cable length
• Comes with mounting plate & screws, pre-soldered connector.

Popular Categories on BuyBestBrands.in