Internal HDD By BUYYART

• Please read the full product description
• Features: With big capacity smoothing capacitor and high power LDO controller chip. Greater stability. Low power consumption. No noise when working. 2-5 times faster reading speed than HDD. For heavy duty. Easy to install.
• Please note: Only support SATA agreement m.2 SSD(B key or B/M tired KEY), does not support PCI-E and NVME agreement m.2 SSD(M key).
• Specification: Suitable SSD Length: 3cm/1.18in, 4.2cm/1.65in, 6cm/2.36in, 8cm/3.15in
• Packing Content: 1 X SSD SATA Adapter

• Feature: 1. Extend the 5 4-pin fan interface to solve the lack of motherboard interface and
• centralize the processing of fan cables. 2. The PWM header is connected to the motherboard CPU fan header, and the red is a dedicated header for CPU fans. The black header is the PWM conventional fan header. 3. Motherboard cpuFAN power input. 4. Support 3-pin fan but without speed regulation function, this is limited by the function of the fan itself, can only run 3-pin fan at full speed.
• Specification: RGB interface: 12V 4Pin, 5V 3Pin Corresponding Interface: Motherboard 12V RGB Interface, Motherboard 5V RGB Interface Can be connected to RGB: 10 Size: 88 X 38 X 14mm/3.46 X 1.5 X 0.55\" Line Length: 50cm/19.69\" Precautions: 1. This hub can't upgrade the extra power supply capability of the RGB interface of the motherboard. Generally, the RGB interface can provide at least 12W power supply
• capability. It can be connected to 10 Aura fans for unified dimming. It is difficult to connect the RGB lamp with a total length of more than 1m/3.28ft. If the interface load is too large, the brightness of the light will become darker obviously then you should reduce the device. 2. Wiring skills: Keep in mind that the arrow mark on the plug corresponds to the RGB pin 12V. 3. The pins of the standard RGB interface are round pins. Individual support for the dimming of mainboard.
• Please confirm whether your motherboard supports it when purchasing. 4. This hub function is to expand the RGB pin and not to supply power to the fan.Notes: 1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! 2. Please allow 1-3mm measuring deviation due to manual measurement. Pakage item=1 X RGB Synchronization HUB 1 X RGB Extension Cable

• The all new 2-1 Thunder Board is the latest All in one M.2 & mSATA SSD to SATA Adapter in the market. Use it to easily connect any of the 6 different size M.2 or mSATA SSDs to any SATA port. Can be used in a 2.5\" HDD enclosure, or mounted in a 2.5\" drive bay. Once connected the M.2 SSD shows on your desktop or laptop computer as a new partition. It can be used as a bootable disk and requires no extra driver.
• Key Features M.2 (NGFF) & mSATA to SATA III Adapter board Suitable for either M.2 SSD or mSATA SSD Green LED indicates power status Red LED indicates active status Thermal shutdown protection Data transfer rate: 6Gb/s up to 520MB/Sec
• Pakage Type : 1pcs M.2 (NGFF) & mSATA to SATA III Adapter board
• Pakage Type : 1pcs M.2 (NGFF) & mSATA to SATA III Adapter board

• Please Read the full product description before purchasing 100% brand new and high quality 9.5mm thick This Hard Drive Adapter lets you add a second hard drive to the laptop systems. With a second hard drive, you can quickly store and back up critical data. Add this caddy to your laptop to give you another hard drive. Simply remove your CD/DVD-ROM drive and put the Caddy (with the added hard drive) in its place... This is a good working adapter and is guaranteed.
• How to use: Unpack the New drive, lift the adapter retaining latch, the screw to the hard disk Insert the drive into the Adapter at an angle Slide the drive into the connector until it locks into place Lower the adapter retaining latch until it snaps closed
• Specifications: Support: SATA Support hard disk: 2.5 HDD, SATA, SATAII SDD Compatible Models: Laptop with a 9.5mm thick DVD-ROM Color: black Size: 125mm*125mm*12.7mm
• Package includes: 1 x 2nd Hard Drive Caddy 4 x Screws

• Please read the full product description Key Features M1: This product supports the SSD defined by msata interface in mini pci-e. msata is not equal to 1.8-inch micro SATA. At the same time, this product also supports the conversion of solid-state hard disk with m.2 ngff SATA protocol to 2.5-inch SATA interface. However, the two kinds of hard disks cannot be used at the same time. If you insert two kinds of hard disks at the same time, you can only read one of them
• 2: There are three pin definitions for the mini PCI-E interface SSD. One is called msata, which is often found on Lenovo and thinpad machines, and can also be called Intel defined interface; the other is called SATA Mini PCI-E, which is commonly seen in ASUS EPC and some tablet computers, also known as ASUS defined interface; and the other is defined by PATA, which is an IDE interface in essence, which is commonly seen in Dell Mini 9. Wait for the machine. The three interface
• definitions look exactly the same and cannot be distinguished by the naked eye, so be sure to distinguish the interface definitions of your SSD! 3: The m.2 ngff SSD has three protocols: SATA protocol, nvme PCIe x2 protocol and nvme PCIe X4 protocol. This adapter card only supports the SATA protocol.
• Specifications: M.2 (NGFF) & mSATA to SATA III Adapter card Support SATA Reversion 3.1 Fully compatible with SATA 3.1 standard Compatible with PCI Express M.2 protocol MSATA Upports full-height and half-height MSATA SSDs M.2(NGFF)Support M.2 SATA SSD(2230 2242 2260 2280)
• Please note: This adapter card supports msata and SATA protocol m.2 ngffssd, but can not use both hard disks at the same time! Switch to ngff to read m.2 ngff SSD, switch to msata to read msata SSD. The adapter card only converts the interface form and does not change any performance Package contain: 1.SATA III Board Adapter

• Brand new and high quality Product Description 100% Brand New and High Quality The Micro SATA SSD adapter has a SATA 22 pin male plug and 16 pin Micro SATA Female socket. The Micro SATA adapter is used to adapt SATA power and data to a Micro SATA drive. The unit has a control power IC in converter that will convert a 5V power source to 3.3V that is required to operate
• the Micro SATA 1.8 inch drives. This adapter can be used to power up your 1.8 inch Micro SATA 3.3V SSD or HDD drive from a 22 pin SATA female receptacle with a DATA signal and a 5V power source. The unit can also be used for 5V drives as it is duel function.
• Compatible Model This adapter can be used to power up your 1.8 inch Micro SATA 3.3V SSD or HDD drive from a 22 pin SATA female receptacle with a DATA signal and a 5V power source.
• Package Includes 1 x 1.8\" Micro SATA SSD HDD to SATA Adapter

Popular Categories on BuyBestBrands.in