Cutting Tools By Drill America

• For use in enlarging or deburring tapered holes
• Commonly used in ball joint studs and tie-rod ends
• Can be used by hand or machine
• Use in a machine with a 1/2 in. chuck, simply remove the T-handle
• High speed steel reamer

• Carbide-tipped tools feature cutting edges of carbide for wear resistance and a steel shank for toughness
• Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications
• SDS Plus shank hammer bit
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Especially suited for drilling in stone or concrete

• Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys
• Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools; performance is similar to uncoated tools
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Manufactured to National Aerospace standard 907

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Ideal for drilling in low and medium tensile strength materials

• High speed steel
• Split Point
• Stub (Screw Machine Length)

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Designed to perform in a broad range of materials in the iron and steel families

• Cobalt taper shank drills are made of heat resistant cobalt.
• Engineered with heavy-duty construction to perform well in tough, hard-to-machine materials.
• Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Designed to perform in a broad range of materials in the iron and steel families

• Made of carbon steel
• Comes with polished finish
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Comes individually packaged
• For woodworking

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Round shanks allow use with a wide variety of toolholding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• For general purpose drilling in applications where extra length for reach is required, designed to perform in a broad range of materials in the iron and steel families

• High Speed Steel
• Hand Reamer
• Bright Finish

• Hex Die
• Standard wrench can be used to turn hex dies
• Bright finish
• Country of origin: United States

• 3/4\" Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment
• Annular cutters are designed for fast, efficient hole making
• Fits most magnetic drill presses
• Lasts longer than high speed steel annular cutters
• Stronger material than high speed steel annular cutters

• Carbide tipped drills feature heavy-duty construction and heat treated body for optimum wear resistance and support of the carbide tip
• Used in the production of cast iron, non-ferrous metals, and many composite materials such as hard rubber or copper alloys
• Not recommended for drilling steel.
• Jobber (standard) flute and overall length

• High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance
• Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge
• Round shanks allow use with a wide variety of tool holding systems
• When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging
• Ideal for drilling in low and medium tensile strength materials

Popular Categories on BuyBestBrands.in