Electrobot 50Pcs 6x6x6 mm Micro Momentary Tactile Tact Touch Push Button Switch (Set of 50) - Product Features
- Micro Momentary Tactile Tact Touch Push Button Switch.
- Size: 6 x 6 x 5mm
- Temperature: -30 ~ +70 Centigrade
- Withstand voltage: AC250V
- Rated load: DC12V 50mA
Electrobot DHT11 Digital Temperature & Humidity Sensor Module for Arduino and RPi - Product Features
- Relative humidity and temperature measurement
- All calibration, digital output
- Excellent long-term stability
- Long distance signal transmission
- Low power consumption
Electrobot EBRTH02 50 Value Resistor Kit (Pack of 1000) - Product Features
- Carbon film resistors, 50+ values
- Quantity: 1000 pieces (20 each)
- Tolerance: 5 percent, power rating: 0.25 watt
- weight: 370 gms
- good quality product
Electrobot Breadboard Jumper Wires Ribbon Cables Kit, Multicolored (120 Pieces) - Product Features
- Cable length: About 21.4 cm/ 8.4 inch (m/ m), 20.7 cm/ 8.1 inch (m/ f), 20 cm/ 7.8 inch (f/ f)
- Including: 1 x 40-pin m/ f jumper wires, 1 x 40-pin m/ m jumper wires, 1 x 40-pin f/ f jumper wires
- Can be separated into the assembly containing the wire quantity you required and to support non-standard odd-spaced headers, suitable for arduino breadboard kit project, pcb project, pc motherboard, etc., Through the pin connection, without welding, fit for fast circuit test
- available in multicolour
Electrobot RFID Starter Kit for UNO R3 from Knowing to Utilizing, Servo, RC522 RFID Module, PS2 Joystick, Learning Kit with Guidebook - Product Features
- A detailed user manual/guidebook(PDF) with 25 lessons is provided.
- It is esay for you to learn UNO R3 Microcontroller and programming.
- Quick-responding technical support for free.
- Re-designed case, it is very beautiful, and it is a best gift for children.
- Arduino UNO R3 Microcontroller is included.
Electrobot HC-06 Wireless transceiver Bluetooth Module for DIY Projects - Product Features
- High-performance wireless transceiver system.
- Wireless transceiver Sensitivity (Bit error rate) can reach -80dBm.
- Has a build-in 2.4GHz antenna; user neednt test antenna.
- Low power consumption.
- Has a 2.4GHz digital wireless transceiver.
Electrobot DS3231 Real Time Clock (RTC) Module for Arduino & Rpi - Product Features
- DS3231 Module is a Bread Board friendly extremely precise I?C real time clock Module.
- DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator.
- Operating voltage :3.3 5 .5 V
- I?C bus interface, the maximum transmission speed of 400KHz (working voltage of 5V)
- Chip temperature sensor comes with an accuracy of ? 3
Electrobot 100 RPM - 12V Centre Shaft DC Geared Motor - Product Features
- It comes with Good Quality Gears.
- The metal gears have better wear and tear properties.
- Gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although motor gives 100 RPM at 12V, motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
- The shaft has a hole for better coupling.
Electrobot KY-026 Flame Sensor Module for Temperature Detecting Suitable for Arduino & Pi - Product Features
- KY-026 Flame Sensor Module IR Sensor Detector
- Extremely sensitive to wave between 760-1100nm, Power Supply: 0-15 V DC
- Comparator chip LM393 makes module readings stable.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Hole Inner Diameter: Approx. 3mm ; Size (L x W): Approx. 36 x 16mm
Electrobot 433/434Mhz RF Transceiver Module For Arduino DIY Projects - Product Features
- The result is excellent performance in a simple-to-use.
- This RF module comprises of an RF transmitter and an RF receiver.
- TX: Power supply and/or modulation input voltage : 2.2 to 5.5v. Operating temperature: -40 to +80C.
- RX: Power supply and/or modulation input voltage :.5v. Operating temperature: -20 to +80C.
- Specifically designed for remote-control and wireless security operating at 315/434Mhz.