Scriptronics 5V One Channel Relay Module Relay Switch with OPTO Isolation High Low Level Trigger Compatible with Arduino Raspberry pi ARM AVR - Product Features
- There is a normally open and one normally closed contact.
- The control DC or AC signal, you can control 220V AC load.
- Blue KF301 terminals to the control line is more convenient.
- With the power supply and relay instructions, pull off, disconnect does not shine.
- The module complies with international safety standards, the control area and the load region isolation trench.
Scriptronics DC 6V~30V Multifunction Trigger Delay Time Module Switch Control Timer Relay Digit LED Display Micro USB 5V With USB Cable for Arduino - Product Features
- The interface is clear and simple, powerful, easy to understand, meet almost all our needs,
- Easy to use, Wide voltage power supply (6 ~ 30V) supports micro USB 5.0V power supply,
- There is a key stop function (STOP key), with reverse polarity protection, reverse polarity does not burn,
- Increase the sleep mode, it enables, without any operation within 5 minutes, turn off the monitor automatically, any key to wake up,
- You can set a different OP, CL, LOP parameters, which are independent of each other, were saved; All setup parameters are saved automatically power down.
Scriptronics Breadboard 830 Point Solderless Prototype PCB Board Kit Protoboard MB-102 for Arduino (Pack of 3) - Product Features
- Completely reusable
- Terminal Strips 630PTS
- Distribution Strips 200pts
- MB102 830 POINTS SOLDER LESS PCB BREAD BOARD PROTOTYPE BOARD
- ABS Plastic Completely reusable Coloured coordinates for easy component placement
Scriptronics TP4056 Type-C Input Interface USB 5V 1A 18650 Lithium Battery Charger Module Charging Board with Dual Protection Function (2 Piece) - Product Features
- Connect Type C cable for power, or 5V DC to pads marked IN+ and IN- on the left-hand side of the module
- Connect cell to charge to B+/B- pads on the right-hand side of the module.
- A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side
- Important! Disconnect load when charging
- The red LED indicates charging in progress, the green LED indicates charging has finished.
Scriptronics NE555 Frequency Adjustable Pulse Generator Module NE555 Chip DEAU (5 Piece) - Product Features
- Input Voltage: 5V-15V DC
- Output amplitude: 4.2V V-PP to 11.4V V-PP.
- Output Current : 15mA for 5V & 35mA for 12V.
- Working voltage: 5-12V
- Minimum 50% duty cycle, 3.7 Hz & Maximum 98% duty cycle, 1.3KHz
Scriptronics Voltage Detection Sensor Module For Arduino, ARM and other MCU (2 Piece) - Product Features
- Voltage input range: DC 0-25V
- Voltage Analog Resolution: 0.00489V
- Voltage detection range: DC 0.02445V-25V
- DC input connector: Terminal cathode connected to VCC, GND negative pole
- Output interface: \"+\" connect 5/3.3V, \"-\" connect GND, \"s\" connect the A_rduino AD pins
Scriptronics ADXL335 3-Axis Accelerometer Angular Transducer Sensor GY-61 Module for Arduino - Product Features
- Power supply: 3 5v
- Supply Current: 400uA
- Operation temperature: 40 Celsius 85 Celsuis
- Analog output communication interface
- Three-axis magnetic field accelerometer module
Scriptronics 40 Pin 2.54mm Male and Female Pin Headers/Berg Strips for Arduino (Pack of 15) - Product Features
- Pitch: 2.54mm with 40 Pin
- Material Type Copper and Plastic
- Best tools for arduino prototype shield
- Good for many applications include industrial, laboratory, personal and hobbies
- Great addition to your hobby craft tool kit. Perfect Product for your saftey and Lab Supply.