Electronics Store - Computer Peripherals - Components - Motherboard

• ESP32-S3 Microcontroller Wi-Fi Development Board with pre-soldered header. Supports Development Environments Such As ESP-IDF, Arduino, MicroPython,Etc. Comprehensive SDK, Dev Resources, Tutorials To Help You Easily Get Started
• MHz. Integrated 512KB SRAM, 384KB ROM, 2MB PSRAM, 16MB Flash memory. Integrated 2.4GHz Wi-Fi and Bluetooth LE dual-mode wireless communication, with superior RF performance. Powerful AI Computing Capability & Reliable Security Features.
• Onboard CH343 and CH334 chips can meet the needs of USB and UART development via a Type-C interface. Onboard DC-DC chip MP28164, high efficiency DC-DC buck-boost chip with load current up to 2A.
• Type-C connector, easier to use. 27 multi-function GPIO pins. Rich peripheral interfaces, including full-speed USB OTG, SPI, I2C, UART, ADC, PWM and DVP (8-bit ~ 16-bit camera interface), LCD interfaces (8-bit ~ 16-bit parallel RGB, I8080, MOTO6800), etc. to achieve various functions flexibly Castellated module allows soldering directly to carrier boards.
• Supports multiple low-power operating states, adjustable balance between communication distance, data rate and power consumption to meet the power requirements of various application scenarios. Supports Raspberry Pi Pico expansion board ecology, suitable for artificial intelligence IoT application development.

• High Quality - Good condition,with high quality ,great performance, solid construction.
• Bigger Angle - 160?Wide Angle could have great angle of view.
• Camera Specifications - The camera is capable of 2592 x 1944 pixel static images,and also supports 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 video recording,with 5MP OV5647 1080p webcam sensor.
• Widely Use - The camera module can fully compatible with Raspberry Pi 4 b 3 b+ / 3 b / 2b / A+ / B+,come with cable to connect raspberry pi Zero,widely use for car photographing, video recording, indoor and outdoor monitoring, aerial photography.
• CSI Interface - This interface uses the dedicated CSI interface, via the CSI bus, a higher bandwidth link which carries pixel data from the camera back to the processor.

• Sensor Chip: TCS3200 (RGB color detector)
• Detects static color, the output is a square wave with frequency directly proportional to incident light intensity
• Supports fill-light by onboard LEDs
• Ambient light sensing and calibration
• Test strip reading

• 100% brand new and high quality
• Driver element: a-Si TFT active matrix
• Resolution (dots): 240RGB*320Dots
• Pixel arrangement: RGB vertical stripe
• With PCB plate (including power supply IC, SD), compatible with 5110 interface

• Supports Intel Core 14th/ 13th /12th processors
• Dual Channel Non-ECC Unbuffered DDR4, 2 DIMMs
• 4+1+1 Hybrid Digital VRM Design
• GbE LAN with Bandwidth Management
• NVMe PCIe 3.0 x4 M.2
• High Quality Audio Capacitors and Audio Noise Guard
• Smart Fan 6 Features Multiple Temperature Sensors , Hybrid Fan Headers with FAN STOP
• GIGABYTE APP Center, Simple and Easy Use
• Anti-Sulfur Resistors Design

• Dev BRD, stm32 F446re Arduino/mbed core nucleo-f446re from STMicroelectronics
• Manufacturer name: STMicroelectronics
• Manufacturer part no: nucleo-f446re

• Powered by 3rd generation AMD Ryzen 9, Ryzen7, Ryzen 5 AM4 to maximize connectivity and speed with lightning M.2, PCIe 4.0, USB 3.2 Gen1 and up to 64GB of DDR4 (4600MHz).
• Core Boost technology combines optimized power circuit layouts and digital power design which allows for precise and steady current delivery to the CPU.
• AUDIO BOOST which rewards your ears with studio grade sound quality for the most immersive gaming experience.
• High level PCB design with a 2oz thickened copper ensure stable power supply, better durability and reliability for high-end CPU.
• Dragon Center: A brand new software which integrates all MSI exclusive tools with user friendly user interface.

• BTB Design BIGTREETECH CB1 core control board features the same board to board header as CM4. Thus BTT CB1 can be directly mounted both on your Rasp-berry Pi and BIGTREETECH Pi4B base board to run klipper in a highly cost-effective way.
• Powerful SystemBTT CB1 adopts quad-core 64-bit Cortex-A53 @1.5GHz processor and Mali G31 MP2 GPU, supporting OpenGL3.2; Equipping with 1GB DDR3 memory chip, CB1 is programmable and powerful to run Linux and supports Debian.
• InterfacesBIGTREETECH CB1 comes with HDMI 2.0A interface to support 4K displays. And also onboard USB2.0 interface.
• Internet InfoBIGTREETECH CB1 core control board supports 100M Ethernet and 100M Wifi 2.4G/802.11 b/g/n.
• Easy to Run KlipperWith the same BTB connector as CM4, CB1 can be directly mounted on BIGTREETECH Manta Series Motherboards: Manta E3EZ/Manta M4P/Manta M5P/Manta M8P to run Klipper easier and more reliable. Combining with BTT Pi4B or Rasp. Pi base board, CB1 can also be used on SKR MINI E3 V3.0/SKR 3/SKR 3 EZ/SKR Pico/Octopus Pro etc. to run Klipper.

• Onboard voltage translator, compatible with 3.3V/5V operating voltage, Compatible with Raspberry Pi, Arduino, STM32 and other motherboards.
• Based on PAJ7620U2 sensor, directly recognises 9 basic gestures (Supported gestures: up, down, left, right, forward, backward, clockwise, anticlockwise, shake), supports gesture interrupt output.
• I2C interface, requires only two signal pins to control.
• Embedded infrared LED and optical lens, be able to work in low-light even dark environment.
• Compared with solutions such as APDS-9960, I have faster recognition speed, higher accuracy, more gesture recognition, and stronger anti-interference, which is suitable for low-power application scenarios such as smart home and robot interaction.

• 0.96 inch display screen , resolution: 128 x 64, view angle: > 160?,support voltage: DC 3.3V-5V
• No need backlight, the display can self-luminous; It has high contrast, bright and crisp dots, even tiny fonts quite readable
• There are no fonts embedded in the OLED controller, users can create fonts through font generation software
• The IIC address can be changed,it is convenient to use with different machines
• With 4 square holes, I2C OLED display module can be installed easily, convenient to use and simple you working

• This breakout board is specially made for Raspberry Pi Pico, with additional pin headers, which are fully compatible with the board
• The pin header and the breakthrough board are not welded, just insert pico after the welding is successful
• The breakthkout board is gold-plated on both sides and holes are plated, and the material of the PCB board is excellent
• The breakout board is equipped with Raspberry Pi pico, which is convenient for users to develop and integrate flexibly
• Note: The package does not include Raspberry Pi pico. This product needs to be assembled and welded by itself

• STM32F401CCU6 84Mhz, 64KB RAM, 256KB ROM
• 25MHZ high speed crystal oscillator & 32.768khz 6PF low speed crystal oscillator
• STM32F401CCU6 support for MicroPython programming with available MicroPython firmware; Support for programming development; Support C language programming development
• STM32F401CCU6 there are 3 buttons, reset key, BOOT0 key, user key

• The best baud rate for GPRS communication is 19200 BPS 8-n-1 (GPRS automatically matches baud rate by default).
• Control via AT commands - Standard Commands: GSM 07.07 07.05 | Enhanced Commands: SIMCOM AT Commands.
• Computer debugging USB-TTL can be. This module is powered by: 5V-26V, 5V 2A power supply is recommended. After plugging in the motherboard, the power supply must be able to supply 2A. The reason is that the GPRS startup current and the maximum to
• Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world.
• Short Message Service - so that you can send small amounts of data over the network (ASCII hexadecimal).

• Luckfox Pico Mini Linux micro developmentboard, based on Rockchip RV1103 chip, integrates ARM Cortex-A7/RISC-V MCU/NPU/ISP processors, 64MB DDR2 memory, 128MB SPI NAND flash, supports a variety of interfaces including MIPI CSI, GPIO, UART, SPI, I2C, USB, etc.
• Micro RV1103 Linux development board integrates single-core ARM Cortex-A7 32-bit core with integrated NEON and FPU, built-in RISC-V MCU supports low power consumption and fast start-up, supports 250ms fast picture capture and loading AI model library at the same time to realize face recognition \"in one second\"
• Built-in Rockchip self-developed 4th generation NPU, features high computing precision and supports int4, int8, and int16 hybrid quantization. The computing power of int8 is 0.5 TOPS, and up to 1.0 TOPS with int4
• Built-in self-developed third-generation ISP3.2, supports 4-Megapixel, with multiple image enhancement and correction algorithms such as HDR, WDR, multi-level noise reduction, etc.
• Features powerful encoding performance, supports intelligent encoding mode and adaptive stream saving according to the scene, saves more than 50% bit rate of the conventional CBR mode so that the images from camera are high-definition with smaller size, double the storage space, built-in 16-bit DRAM DDR2, which is capable of sustaining demanding memory bandwidths, integrated with built-in POR, audio codec and MAC PHY

• Standalone Crypto Processor: The TPM is a separate cryptographic processor attached to the motherboard daughter board. The TPM securely stores encryption keys that can be created using encryption software.
• Prevent Access: Without this key, the content on the user's PC remains encrypted and protected from unauthorized access.
• Function: A secure cryptographic processor that helps you perform operations such as generating, storing, and restricting the use of cryptographic keys.
• Wide Application: TPM1.2 encryption security module is commonly used in multi brand motherboards. Some motherboards require a TPM module inserted or an update to the latest BIOS to enable the TPM option. Please note that this is still TPM1.2.
• PCB Material: TPM module adopts PCB material to ensure stable performance, high work efficiency, convenient operation and good durability.

Popular Categories on BuyBestBrands.in